Husqvarna F2303Q0 Скачать руководство пользователя страница 259

Страница: 259 / 322

LUBRICATION SYSTEM 20

- Position special tool

(i}

with the O-ring. Mount and tighten

the screws.
Guideline

Screw, oil filter cover

10 Nm (7.4 lbf ft)

Oil pressure adapter (79429094000) (

p. 306)

Connect the pressure testing tool to the special tool without

the T-plate.

Pressure testing tool (61029094000) (

p. 300)

- Check the engine oil level. (

p. 252)

Danger

Danger of poisoning

Exhaust gases are toxic and

inhaling them may result in unconsciousness and

death.

- Always make sure there is sufficient ventilation

when running the engine.

- Use effective exhaust extraction when starting or

running the engine in an enclosed space.

- Start the engine and let it warm up.

- Check the oil pressure.

Oil pressure

Engine oil temperature:

80 °C (176 °F)

Engine speed: Idle

speed

Engine oil temperature:

80 °C (176 °F)

Engine speed:

6,000 rpm

0.6 bar (9 psi)

1 . 7 bar (25 psi)

If the measured value is less than the specification:

- Check the oil pumps for wear. Check all oil channels

for free flow.

- Switch off the engine.

Warning

Danger of burns

Some vehicle components get

very hot when the machine is driven.

- Wear appropriate protective clothing and safety

gloves. In case of burns, rinse immediately with

lukewarm water.

- Remove the special tools.

- Grease the O-ring of the oil filter cover. Mount the oil filter

cover.

- Mount and tighten the screws.

Guideline

Screw, oil filter cover

110 Nm (7.4 lbf ft)

257

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды