Husqvarna F2303Q0 Скачать руководство пользователя страница 42

Страница: 42 / 322

6 FORK, TRIPLE CLAMP

Main work

- Remove indicator lamp holder.

- Open cable holder

on the left and detach the wiring har-

ness.

- Remove screw

Take off the upper triple clamp with the handlebar and place

to one side.

Info

Cover the components to protect them against dam

age.

Do not kink the cables and lines.

- Remove 0-ring

- Remove protective ring

- Remove the lower triple clamp with the steering stem.

- Remove the upper steering head bearing.

6.22

Installing the lower tri�le clam�

800221-10

Main work

- Clean the bearing and sealing elements, check for damage,

and grease.
I High viscosity grease (

p. 292)

- Insert the lower triple clamp with the steering stem. Mount

the upper steering head bearing.

- Check whether upper steering head seal

is correctly posi

tioned.
Slide on protective ring

and 0-ring

@).

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды