Husqvarna F2303Q0 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 322

background image

5.4

402001-10

400733-01

MOTORCYCLE 5

Remove plug-in stand

O.

Shift the transmission to neutral position.

Condition

Ambient temperature: < 20 °C (< 68 °F)

Push the cold start button in all the way.

Press the electric starter button 0.

Info

Press the electric starter button for a maximum of

5 seconds. Wait for 30 seconds before a further

attempt at starting.
At temperatures below 15 °C (60 °F), several attempts
at starting may be necessary to warm-up the lithium
ion battery and thereby increase the starting power.

During the starting process, the malfunction indicator

lamp lights up.

41

Starting the motorc cle to check the function

Danger

Danger of poisoning

Exhaust gases are toxic and inhaling them may result in unconsciousness and

death.

Always make sure there is sufficient ventilation when running the engine.

Use effective exhaust extraction when starting or running the engine in an enclosed space.

400733-01

Shift the transmission to neutral position.

Press the electric starter button Cl)_

•

Info

I

Press the electric starter button for at most 5 seconds.

Wait for 30 seconds before a further attempt at start
ing.
At temperatures below 15 °C (60 °F), several attempts
at starting may be necessary to warm-up the lithium
ion battery and thereby increase the starting power.

During the starting process, the malfunction indicator

lamp lights up.

Do not open the throttle.

41

13

«
...
13
14
15
16
17
...
»

Содержание F2303Q0



































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для F2303Q0

Бренд: Xenith Страницы: 17

Бренд: hepco & becker Страницы: 4

Бренд: Sicor Страницы: 2

Daytona 955i 2002

Бренд: Triumph Страницы: 384

Бренд: hepco & becker Страницы: 4

Бренд: G PLAST Страницы: 4

Бренд: hepco & becker Страницы: 2

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 278

Бренд: HJC Страницы: 7

LEDV46-T-TS LIGHT KIT

Бренд: AdMore Lighting Страницы: 4

Бренд: Shark Страницы: 28

Бренд: Ultra-tow Страницы: 6

Бренд: HYOSUNG Страницы: 101

Бренд: Bell Sports Страницы: 20

Бренд: Benelli Страницы: 243

Ranger XP900 A-Arms

Бренд: SuperATV Страницы: 6

Бренд: Abus Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды