Husqvarna F2303Q0 Скачать руководство пользователя страница 114

Страница: 114 / 322

12 FUEL TANK, SEAT, TRIM

Mount fuel connection

(i}

with the gasket but do not tighten

yet.

- Tighten nut

Guideline

Nut, fuel pump fas

tener

M12x1.75

- Tighten fuel connection

Guideline

Fuel connection on

fuel tank

Finishing work

M8x1 .25

Install the fuel tank. (

ra!l

p. 103)

Mount the seat. (

ra!l

p. 101)

Install the air filter box cover. (

p. 96)

Install the right side cover. (

p. 100)

15 Nm (11 .1 lbf ft)

10 Nm (7.4 lbf ft)

12.12 Changing the fuel screen

112

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.
-

Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.

Switch off the engine for refueling.

Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

If any fuel is spilled, wipe it off immediately.

Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

- Avoid skin, eye and clothing contact with fuel.
-

Immediately consult a doctor if you swallow fuel.

Do not inhale fuel vapors.

In case of skin contact, rinse the affected area with plenty of water.

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

Change your clothing in case of fuel spills on them.

Note

Environmental hazard

Improper handling of fuel is a danger to the environment.

Do not allow fuel to enter the groundwater, the soil, or the sewage system.

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды