Husqvarna F2303Q0 Скачать руководство пользователя страница 132

Страница: 132 / 322

14 WHEELS

Check that the chain guide is firmly seated.

If the chain guide is loose:

- Tighten the screws on the chain guide.

Guideline

Remaining

screws, chassis

10 Nm (7.4 lbf ft)

Finishing work

Remove the motorcycle from the lift stand.

(

p. 12)

14.8.7

Checking for chain dirt accumulation

400678-01

Check the chain for coarse dirt accumulation.

If the chain is very dirty:

Clean the chain. (

p. 130)

14.8.8

Cleaning the chain

130

Warning

Danger of accidents

Lubricants on the tires reduces the road grip.

Remove lubricants from the tires using a suitable cleaning agent.

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

- Always keep the brake discs free of oil and grease.
-

Clean the brake discs with brake cleaner when necessary.

Note

Environmental hazard

Hazardous substances cause environmental damage.

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

The service life of the chain depends largely on its maintenance.

Preparatory work

Raise the motorcycle with a lift stand. (

p. 12)

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды