Husqvarna F2303Q0 Скачать руководство пользователя страница 143

Страница: 143 / 322

15.8

15.9

WIRING HARNESS, BATTERY 15

Install the air filter box cover. (

p. 96)

...

Checking the open-circuit current

Checking the capacitor

601204-10

Preparatory work

Press and hold the kill switch � while the engine is idling until

the engine stops.

Remove the air filter box cover. (

p. 96)

Remove the seat. (

p. 1 00)

Disconnect the negative cable of the 12 V battery. (

p. 136)

Main work

Measure the current between 12 V battery ground (-) and the

negative cable.

Info

The value of the open-circuit current applies only to
vehicles in the original condition, i.e., without addi
tional power consumers.

��

imum open-circuit cur-

< 1.0 mA

If the measured value is greater than the specified value:

Disconnect the voltage regulator from the wiring har

ness and perform the measurement again.

Check the capacitor. (

p. 141)

Finishing work

Connect the negative cable of the 12 V battery. (

p. 136)

Mount the seat. (

p. 101)

Install the air filter box cover. (

p. 96)

Condition

The 12 V battery is disconnected.

Remove the capacitor.

Discharge the capacitor by bridging the two contacts.

Connect the capacitor to a 12 V test lamp to a connection

and connect to the 12 V battery as shown in the figure.

Info

As the capacitor charge increases, the test lamp
becomes dimmer.

The bulb lights up for: 0.5 ... 2.0 s
The capacitor is OK.

The bulb lights up for: < 0.5 s

Change the capacitor.

The bulb lights up for: > 2.0 s

Change the capacitor.

...

141

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды