Husqvarna F2303Q0 Скачать руководство пользователя страница 61

Страница: 61 / 322

SHOCK ABSORBER, LINK FORK 9

Check the static sag of the shock absorber. (

p. 56)

Check the riding sag of the shock absorber. (

p. 57)

Adjust the rebound damping of the shock absorber. (

p. 55)

Remove the motorcycle from the lift stand. (

p. 12)

9.9

Removin the shock absorber

Preparatory work

Raise the motorcycle with a lift stand.

(

p. 12)

Main work

Remove the cable ties.

Remove screws

with the washers.

Remove the frame protectors on the left and right.

Remove screw

fD.

Remove fitting

C,.

•

Info

Raise the wheel slightly to be able to remove the

screws more easily.

Press angle lever

toward the rear.

Press linkage lever

downward.

Remove screws @.
Pull off foot brake cylinder from the push rod.

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды