Husqvarna F2303Q0 Скачать руководство пользователя страница 38

Страница: 38 / 322

6 FORK, TRIPLE CLAMP

-8

202103-10

Tighten air cartridge

@).

Guideline

Damper cartridge

on outer tube

M51x1 .5

Ring wrench (T14017) (

ral

p. 310)

Right fork leg

50 Nm (36.9 lbf ft)

Clamp the inside fork tube using the axle clamp.
Guideline

Use soft jaws.

Mount the special tool.

Protecting sleeve (T1401) (

p. 310)

Grease and push on dust boot

Lubricant (T14034) (

ral

p. 292)

✓ The sealing lip is mounted with the spring expander

facing down.

Info

Always change the dust boot, seal ring, lock ring,
and support ring.

Push on lock ring

Grease and push on seal ring

Lubricant (T14034) (

ral

p. 292)

✓ The sealing lip points downward, the open side

upward.

Remove the special tool.

Push on support ring

C,.

Sand the edges of the slide bearings with 600 grit sand-
paper; then clean and grease the bearings.

Fork oil (SAE 4) (48601166S1) (

p. 291)

Slide on lower slide bearing

Mount upper slide bearing (D.

Info

Without using a tool, pull the stack slightly apart
by hand.

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды