Husqvarna F2303Q0 Скачать руководство пользователя страница 35

Страница: 35 / 322

6.19

Assembling the fork legs

-8

202103-10

FORK, TRIPLE CLAMP 6

- Mount and tighten valve core

48 .

- Fill the cartridge with air .

Guideline

Minimum air pressure
Maximum air pressure

7 bar (1 02 psi)
15 bar (218 psi)

- Adjust air pressure with special tool 41) as per specifications.

Guideline

Air pressure

111.0 bar (160 psi)

Fork airpump (79412966000) (

il!:!I

p. 304)

- Mount protection cap

C,.

Preparatory work

- Check the fork legs. (

IUI

p. 28)

Left fork leg

- Clamp the inside fork tube using the axle clamp.

Guideline

I Use soft jaws.

- Mount the special tool.

I Protecting sleeve (T1401) (

IUI

p. 310)

- Grease and push on dust boot

I Lubricant (T14034) (

IUI

p. 292)

✓ The sealing lip is mounted with the spring expander

facing down.

•

Info

Always change the dust boot, seal ring, lock ring,

and support ring.

- Push on lock ring

- Grease and push on seal ring

fD.

I Lubricant (T14034) (

IUI

p. 292)

✓ The sealing lip points downward, the open side

upward.

- Remove the special tool.

- Push on support ring

- Sand the edges of the slide bearings with 600 grit sand-

paper; then clean and grease the bearings.

I Fork oil (SAE 4) (48601166S1) (

IUI

p. 291)

- Slide on lower slide bearing

- Mount upper slide bearing (D.

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды