Husqvarna F2303Q0 Скачать руководство пользователя страница 142

Страница: 142 / 322

15 WIRING HARNESS, BATTERY

15.7

140

Alternative 2

UK battery charger

XCharge-professional

(00029095052) (

p. 295)

Alternative 3

CH battery charger

XCharge-professional

(00029095053) (

p. 295)

•

Info

Follow the instructions of the charger and the manual.

- Disconnect the battery charger after charging the 12 V bat

tery.

Guideline

The charging current, charging voltage, and charging time

must not be exceeded.

Recharge the 12 V battery

3 months

regularly when the motorcy-

cle is not being used

Finishing work

- Connect the negative cable of the 12 V battery. (

p. 136)

- Mount the seat. (

p. 101)

- Install the air filter box cover. (

p. 96)

Checking the charging voltage

Condition

The 12 V battery must be fully functional and completely

charged.

Preparatory work

- Remove the air filter box cover. (

p. 96)

- Remove the seat. (

p. 100)

Main work

- Pull back the positive terminal cover.

- Start the motorcycle to check the function. (

p. 13)

Measure the voltage between the specified points.

Measuring point

plus

(+) - Measuring point

Ground(-)

Charging voltage

5,000 rpm

113.5 ... 15.0 V

If the displayed value is less than the specified value:

- Check the plug-in connections from the alternator to

the voltage regulator.

- Check the plug-in connections from the voltage regu-

lator to the wiring harness.

- Check the stator winding of the alternator. (

p. 260)

If the displayed value is greater than the specified value:

- Change the voltage regulator.

Finishing work

- Mount the seat. (

p. 101)

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды