Husqvarna F2303Q0 Скачать руководство пользователя страница 91

Страница: 91 / 322

9.32

9.33

SHOCK ABSORBER, LINK FORK 9

Checking the heim joint for Ria�

T01328-10

Changing the heim joint

Preparatory work

Raise the motorcycle with a lift stand. (

ra:!l

p. 12)

Place a load on the front of the vehicle.

✓ The rear wheel is not in contact with the ground.

Main work

Move the link fork up and down.

If there is detectable play:

Change the heim joint. (

p. 89)

Finishing work

Remove the load from the front of the vehicle.

Remove the motorcycle from the lift stand. (

ra:!l

p. 12)

Preparatory work

Raise the motorcycle with a lift stand. (

p. 12)

Remove the shock absorber. (

p. 59)

Main work

Clamp the shock absorber into the vise.
Guideline

Use soft jaws.

Remove both collar bushings

of the heim joint with a spe

cial tool.

Drift (T120) (

ra:!l

p. 308)

Press the heim joint against a lock ring using the special tool.

Pressing tool (T1207S) (

ra:!l

p. 309)

Remove second lock ring

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды