Husqvarna F2303Q0 Скачать руководство пользователя страница 99

Страница: 99 / 322

11.4

11.5

AIR FILTER 11

lnstallin the air filter

Main work

Detach retaining tab

Remove air filter with air filter support.

Remove air filter from air filter support.

Main work

Mount the clean air filter on the air filter support.

Grease the air filter in area f).

Long-life grease (

p. 292)

Insert air filter and position retaining pin

in bushing

✓ The air filter is correctly positioned.

Insert retaining tab

(D.

✓ Retaining pin

is secured by retaining tab

(D.

Info

If the air filter is not mounted correctly, dust and dirt

may enter the engine and result in damage.

Finishing work

Install the air filter box cover. (

p. 96)

Cleanin the air filter and air filter box

Note

Environmental hazard

Hazardous substances cause environmental damage.

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

Do not clean the air filter with fuel or petroleum since these substances attack the foam.

Preparatory work

Remove the air filter box cover. (

p. 96)

Remove the air filter. (

p. 96)

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды