Husqvarna F2303Q0 Скачать руководство пользователя страница 258

Страница: 258 / 322

20 LUBRICATION SYSTEM

Finishing work

- Check the engine oil level. (

p. 252)

Adding engine oil

Info

Too little engine oil or poor-quality engine oil will result in premature wear of the engine.

20.5

256

�--

Main work

- Remove filler plug

with the O-ring.

- Fill engine oil to the middle

of the level viewer.

- Add the same engine oil used when the last oil change was

carried out.

I Engine oil (SAE 1 0W/50) (

p. 290)

•

Info

For optimal performance of the engine oil, do not mix

different types of engine oil.

We recommended changing the engine oil when nec

essary.

- Mount and tighten the filler plug together with the O-ring.

Danger

Danger of poisoning

Exhaust gases are toxic and

inhaling them may result in unconsciousness and

death.

- Always make sure there is sufficient ventilation

when running the engine.

- Use effective exhaust extraction when starting or

running the engine in an enclosed space.

- Start the engine and check for tightness.

Finishing work

- Check the engine oil level. (

p. 252)

Main work

- Place an appropriate container under the engine.

- Remove screws

Remove the oil filter cover with the O-

ring.

- Remove the oil filter.

I Lock ring plier (51012011000) (

p. 297)

...

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды