Husqvarna F2303Q0 Скачать руководство пользователя страница 152

Страница: 152 / 322

16 BRAKE SYSTEM

150

•

Info

Overfilling the brake fluid reservoir is prevented.

- Tighten the bleeder screw. Remove the bleeder bottle hose.

Attach the protection cap.

- Disconnect the bleeding device. Remove the bleeder cover.
- Fill brake fluid up to the MAX marking.

I Brake fluid DOT 4 / DOT 5.1 (

ll!:!I

p. 290)

- Position the cover with the membrane. Mount and tighten the

screws.

Info

Clean up overflowed or spilled brake fluid immediately

with water.

- Check the hand brake lever for a firm pressure point.

Checkin the brake linin s of the rear brake

Warning

Danger of accidents

Worn-out brake linings reduce the braking effect.

- Ensure that worn-out brake linings are replaced immediately.

- Check the brake linings for minimum thickness f).

I Minimum thickness f)

I � 1 mm (� 0.04 in)

If the minimum thickness is less than specified:

- Change the rear brake linings. (

ll!:!I

p. 150)

- Check the brake linings for damage and cracking.

If damage or wear is encountered:

- Change the rear brake linings. (

ll!:!I

p. 150)

Changing the rear brake linings

Warning

Danger of accidents

Incorrect servicing will cause the brake system to fail.

- Ensure that service work and repairs are performed professionally.

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды