Husqvarna F2303Q0 Скачать руководство пользователя страница 119

Страница: 119 / 322

14.3

WHEELS 14

Check the tire age.

Info

The tire date of manufacture is usually contained in
the tire label and is indicated by the last four digits
of the

DOT

number. The first two digits indicate the

week of manufacture and the last two digits the year
of manufacture.

Husqvarna Motorcycles recommends that the tires be

changed after 5 years at the latest, regardless of the
actual state of wear.

If the tires are more than 5 years old:

Change the tires.

Checking the wheel bearing for �la�

Preparatory work

Raise the motorcycle with a lift stand. (

p. 12)

Place a load on the rear of the vehicle.

✓ The front wheel is not in contact with the ground.

Main work

Move the front wheel from side to side.

Info

Hold the fork leg to check it.

If there is detectable play:

Change front wheel bearing. (

p. 122)

Place a load on the front of the vehicle.

✓ The rear wheel is not in contact with the ground.

Move the rear wheel from side to side.

Info

Hold the link fork to check it.

If there is detectable play:

Change the rear wheel bearing. (

p. 133)

Finishing work

Remove the motorcycle from the lift stand. (

p. 12)

117

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды