Husqvarna F2303Q0 Скачать руководство пользователя страница 150

Страница: 150 / 322

16 BRAKE SYSTEM

148

Note

Environmental hazard

Hazardous substances cause environmental damage.

- Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

Never use DOT 5 brake fluid. It is silicone-based and purple in color. Oil seals and brake lines are not

designed for DOT 5 brake fluid.

Avoid contact between brake fluid and painted parts. Brake fluid attacks paint.

Only use clean brake fluid from a sealed container.

Preparatory work

- Check the front brake linings. (

p. 144)

Main work

- Move the brake reservoir mounted on the handlebar to a hori-

zontal position.

- Remove screws

- Take off cover

with membrane (D.

- Fill brake fluid up to the MAX marking.

I Brake fluid DOT 4

DOT 5.1 (

p. 290)

- Position the cover with the membrane. Mount and tighten the

screws.

Info

Clean up overflowed or spilled brake fluid immediately

with water.

Changing the front brake fluid

Warning

Skin irritation

Brake fluid causes skin irritation.

- Keep brake fluid out of the reach of children.

- Wear suitable protective clothing and safety glasses.

- Do not allow brake fluid to come into contact with the skin, the eyes or clothing.

- Consult a doctor immediately if brake fluid has been swallowed.

- Rinse the affected area with plenty of water in the event of contact with the skin.

...

- Rinse eyes thoroughly with water immediately and consult a doctor if brake fluid comes into contact

with the eyes.

- If brake fluid spills on to your clothing, change the clothing.

Note

Environmental hazard

Hazardous substances cause environmental damage.

- Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды