Husqvarna F2303Q0 Скачать руководство пользователя страница 144

Страница: 144 / 322

15 WIRING HARNESS, BATTERY

601204-11

15.10 Checking the starter rela¥

601201-10

142

- Discharge the capacitor with a 12 V test lamp, as shown in

the figure.

Info

As the capacitor charge decreases, the test lamp

becomes dimmer.

» The bulb lights up for: 0.5 ... 2.0 s

The capacitor is OK.

» The bulb lights up for: < 0.5 s

Change the capacitor.

» The bulb lights up for: > 2.0 s

Change the capacitor.

- Install the capacitor.

Preparatory work

...

- Press and hold the kill switch � while the engine is idling until

the engine stops.

- Remove the air filter box cover. (

p. 96)

- Remove the seat. (

ra!l

p. 100)

- Disconnect the negative cable of the 12 V battery. (

ra!l

p. 136)

Main work

- Pull starter relay

from the holder.

- Unplug connector

- Pull back the cover.

- Detach cables

from the starter relay.

- Connect the starter relay to a 12 V power supply as per the

figure.

- Measure the resistance between the specified points.

I Resistance of open circuit I O

If the value displayed does not meet specifications:

- Change the starter relay.

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды