Husqvarna F2303Q0 Скачать руководство пользователя страница 236

Страница: 236 / 322

17 ENGINE

17.5.22 Installing the rotor

17.5.23 Installing the piston

310076-10

310077-10

310078-10

234

- Mount the woodruff key.

- Mount the rotor.

- Mount and tighten nut

with the spring washer.

Guideline

Nut, rotor

M12x1

60 Nm (44.3 lbf ft)

Thread, oiled with

engine oil/cone

degreased

- Move the joints of the compression ring and oil scraper ring

so they are offset by 180

- Place the oiled piston on the cylinder.

- Clamp the piston rings together using the special tool.

I Piston ring compressor (60029015000) (

p. 299)

- Tap lightly on the piston ring compressor from the top with a

plastic hammer so that it lies flush with the cylinder.

✓ The special tool must press the piston rings together

properly and lie flush with the cylinder.

- Drive the piston into the cylinder by striking it carefully with

the hammer handle.
✓ The piston rings should not catch or they will be dam

aged.

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды