Husqvarna F2303Q0 Скачать руководство пользователя страница 129

Страница: 129 / 322

WHEELS 14

14.8.5

Adjusting the chain tension

Warning

Danger of accidents

Incorrect chain tension damages components and results in accidents.

If the chain is tensioned too much, the chain, engine sprocket, rear sprocket, transmission and rear

wheel bearings wear more quickly. Some components may break if overloaded.

If the chain is too loose, the chain may fall off the engine sprocket or the rear sprocket. As a result, the

rear wheel locks or the engine will be damaged.

- Check the chain tension regularly.

- Set the chain tension in accordance with the specification.

Preparatory work

- Raise the motorcycle with a lift stand. (

IUI

p. 12)

- Check the chain tension. (

IUI

p. 126)

Main work

- Loosen nut

- Loosen nuts

- Adjust the chain tension by turning adjusting screws @) left

and right.
Guideline

Chain tension

155 ... 58 mm (2.17 ...

2.28 in)

Turn adjusting screws @) on the left and right so that the

markings on the left and right chain adjusters are in the

same position relative to reference marks t). The rear

wheel is then correctly aligned.

- Tighten nuts

- Make sure that chain adjusters

are fitted correctly on

adjusting screws

- Tighten nut

Guideline

Nut, rear wheel spin- M25x1 .5

die

•

Info

80 Nm (59 lbf ft)

The wide adjustment range of the chain adjusters

(32 mm (1 .26 in)) enables different secondary ratios

with the same chain length.

Chain adjusters

can be turned by 180

Finishing work

- Remove the motorcycle from the lift stand. (

IUI

p. 12)

14.8.6

Checking the chain, rear sprocket, engine sprocket, and chain guide

Preparatory work

- Raise the motorcycle with a lift stand. (

IUI

p. 12)

127

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды