Husqvarna F2303Q0 Скачать руководство пользователя страница 64

Страница: 64 / 322

9 SHOCK ABSORBER, LINK FORK

9.11

Position the frame protectors on the left and right.

- Mount and tighten screws@).

Guideline

I Screw, frame pro

tector

Nm (2.2 lbf ft)

- Mount and tighten screws

with the washers.

Guideline

Screw, frame pro

tector

- Mount the new cable ties.

Finishing work

3 Nm (2.2 lbf ft)

- Remove the motorcycle from the lift stand. (

p. 12)

- Check the free travel of the foot brake lever. (

p. 152)

Checking the shock absorber linkage

Preparatory work

- Raise the motorcycle with a lift stand. (

p. 12)

Main work

- Remove screw

- Remove fitting

Info

Raise the wheel slightly to be able to remove the

screws more easily.

- Remove fitting

@).

- Take off the angle lever.

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды