Husqvarna F2303Q0 Скачать руководство пользователя страница 28

Страница: 28 / 322

6 FORK, TRIPLE CLAMP

B03553-10

B03554-10

- Remove the piston rod with the seal ring retainer.

- Degrease and clamp the top of the piston rod.

I Clamping stand (T14016S) (

p. 310)

- Heat up the thread area of the piston.

Guideline

I 50 °C (122 °F)

Remove piston (D.

- Remove end stop @.

- Remove spring

with spring support

and spring sup-

port Ci).

- Remove seal ring retainer

6.15

Disassembling the shock absorber cartridge

Preparatory work

- Disassemble the fork legs. (

p. 21)

Main work

- Allow oil to drain from breathing hole

- Degrease and clamp the top of the shock absorber cartridge.

I Clamping stand (T14072) (

p. 311)

- Loosen screw cap

Special socket (T14084) (

p. 311)

- Remove the screw cap with shock absorber unit

fD.

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды