Husqvarna F2303Q0 Скачать руководство пользователя страница 191

Страница: 191 / 322

310058-10

ENGINE 17

Main work

Remove all remaining dowels.
Remove oil nozzle

Remove screws

and take off the bearing retainers.

Remove the bearing retainer from main shaft bearing

countershaft bearing

C,,

and shift drum bearing

Remove any remnants of sealing compound and clean the

section of the engine case thoroughly.

Warm the section of the engine case in an oven.
Guideline
1150 oc (302 OF)

Knock the section of the engine case against a level wooden

board. This will cause the bearings to drop out of the bearing

seats.

Info

Any bearings that remain in the section of the engine

case must be removed using a suitable tool.

Remove washer

CD.

Warm the section of the engine case again.
Guideline

1150 °C (302 °F)

Position washer

CD.

Insert the new cold bearings into the bearing seats of the hot

section of the engine case and, if necessary, use a suitable

press drift to push the bearings from the inside to the out

side, all the way to the stop or until flush.

Info

When pressing in, ensure that the section of the

engine case lies flat in order prevent damage.

Only press the bearings in using the outer bearing

race; otherwise, the bearings will be damaged when

they are pressed in.

After the section of the engine case has cooled, check that

the bearings are firmly seated.

•

Info

If the bearings are not firmly seated after cooling, it

is likely that they will rotate in the engine case when

warm. In this case, the engine case must be renewed.

Position all bearing retainers. Mount and tighten the screws.

Guideline

Screw, bearing

retainer

Mount and tighten oil nozzle

6 Nm (4.4 lbf ft)

Loctite

243

™

189

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды