Husqvarna F2303Q0 Скачать руководство пользователя страница 246 | Manualshive

Страница: 246 / 322

background image

18 CLUTCH

244

Changing the h}!draulic clutch fluid

Warning

Skin irritation

Brake fluid causes skin irritation.

-

Keep brake fluid out of the reach of children.

-

Wear suitable protective clothing and safety glasses.

-

Do not allow brake fluid to come into contact with the skin, the eyes or clothing.

-

Consult a doctor immediately if brake fluid has been swallowed.

-

Rinse the affected area with plenty of water in the event of contact with the skin.

-

Rinse eyes thoroughly with water immediately and consult a doctor if brake fluid comes into contact

with the eyes.

-

If brake fluid spills on to your clothing, change the clothing.

Note

Environmental hazard

Hazardous substances cause environmental damage.

-

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

Never use DOT 5 brake fluid. It is silicone-based and purple in color. Oil seals and clutch lines are not

designed for DOT 5 brake fluid.
Avoid contact between brake fluid and painted parts. Brake fluid attacks paint.
Only use clean brake fluid from a sealed container.

-

Move the clutch fluid reservoir mounted on the handlebar to a

horizontal position.

-

Remove screws

O.

-

Take off cover

8

with membrane

8.

Fill bleeding syringe

C,

with the appropriate hydraulic fluid.

Syringe (50329050000) (

a

p. 296)

Brake fluid DOT 4 / DOT 5.1 (

a

p. 290)

-

On the clutch slave cylinder, remove the protection cap and
mount bleeding syringe

C,

with appropriate hose piece at

the bleeder screw

0.

Only loosen bleeder screw

0

on the clutch slave cylinder to

the point where filling is possible.

«
...
244
245
246
247
248
...
»

Содержание F2303Q0



































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для F2303Q0

750 Sport Bevel Heaven

Бренд: Ducati Страницы: 235

Бренд: Baja motorsports Страницы: 8

Бренд: Yukon Trail Страницы: 24

Бренд: kellermann Страницы: 2

Бренд: BMW Motorrad Страницы: 146

Бренд: Vance and hines Страницы: 5

Бренд: hepco & becker Страницы: 2

Бренд: hepco & becker Страницы: 3

Бренд: Kinroad Страницы: 25

MS3 - CATALOGUE

Бренд: HYOSUNG Страницы: 104

Бренд: MT Helmets Страницы: 9

TORNADO Tre Novecento 900

Бренд: Benelli Страницы: 48

Бренд: Benelli Страницы: 108

Бренд: hepco & becker Страницы: 4

Бренд: Yadea Страницы: 66

Бренд: Livall Страницы: 52

Бренд: Livall Страницы: 112

Бренд: Honda Страницы: 89

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды