Husqvarna F2303Q0 Скачать руководство пользователя страница 229

Страница: 229 / 322

17.5.9

Installing the locking lever

ENGINE 17

- Mount locking lever

with the washer, sleeve and spring.

- Mount and tighten screw

Guideline

Screw, locking

lever

6 Nm (4.4 lbf ft)

Loctite

243

™

...

17 .5.10 Installing the shift drum locating unit

17 .5.11 Installing the shift shaft

17.5.12 Installing the force pump

- Push away locking lever

from the shift drum locating unit

and position the shift drum locating unit

•

Info

The flat areas of the shift drum locating unit are not

symmetric.

- Relieve tension from the locking lever.

- Mount and tighten screw (i).

Guideline

Screw, shift

drum locating

10 Nm (7.4 lbf ft)

Loctite

243

™

- Slide shift shaft

with the washer into the bearing seat.

Push sliding plate

away from the shift drum locating unit

and insert the shift shaft all the way.

- Let the sliding plate engage in the shift drum locating

unit (i).
Shift through the transmission.

...

Oil the oil pump shaft, internal rotor, and external rotor before

assembly.

- Mount oil pump shaft

Mount pin@.

- Mount the internal rotor with the recess facing inward.

Mount external rotor (i) with the bevel facing inward.

227

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды