Husqvarna F2303Q0 Скачать руководство пользователя страница 249

Страница: 249 / 322

CLUTCH 18

- Check 0-ring

for damage.

If the 0-ring is damaged:

- Change the 0-ring.

- Lubricate the 0-ring with engine oil and position the clutch

cover.

- Mount screws

but do not tighten yet.

Guideline

Screw, clutch cover

M6x25

10 Nm (7.4 lbf ft)

- Mount screw

but do not tighten yet.

Guideline

Screw, clutch cover

M6x55

110 Nm (7.4 lbf ft)

- Mount screw

but do not tighten yet.

- Tighten all screws in a crisscross pattern.

Guideline

Screw, clutch cover

- Attach spring

Finishing work

- Stand the motorcycle upright.

Danger

10 Nm (7.4 lbf ft)

Danger of poisoning

Exhaust gases are toxic and

inhaling them may result in unconsciousness and

death.

- Always make sure there is sufficient ventilation

when running the engine.

- Use effective exhaust extraction when starting or

running the engine in an enclosed space.

- Start the engine and check that it is oil-tight.

- Check the engine oil level. (

�

p. 252)

247

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды