Husqvarna F2303Q0 Скачать руководство пользователя страница 147

Страница: 147 / 322

BRAKE SYSTEM 16

Remove screws

with washers

Press back the brake linings by slightly tilting the brake

caliper laterally on the brake disc. Pull the brake caliper
carefully back from the brake disc and hang to the side.

Info

Do not operate the hand brake lever if the brake

caliper has been removed.

Move the brake reservoir mounted on the handlebar to a hori

zontal position.

Remove screws

Take off cover

with membrane

Press the brake piston back into the basic position and

ensure that brake fluid does not flow out of the brake fluid
reservoir; extract some if necessary.

Press together brake linings (D and remove them from the

brake caliper.

Clean the brake caliper and spring plate.

Ensure that the spring plate is correctly positioned.

Info

The arrow on the spring plate points in the direction of
rotation of the brake disc.

Position the new brake linings (D in the guides and press

toward the pistons.

✓ The spring plate is seated correctly in the brake caliper.

Info

Always change the brake linings in pairs.

145

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды