Husqvarna F2303Q0 Скачать руководство пользователя страница 207

Страница: 207 / 322

Check timing chain

for damage and wear.

If there is damage or wear:

Replace the timing chain.

ENGINE 17

Check the timing chain links for smooth operation. Let the timing chain hang down freely.

The chain links no longer align in a straight line:

Replace the timing chain.

17 .4.26 Removing the rocker arm

310097-10

17 .4.27 Removing the valves

Remove screws

and

of the rocker arm shafts.

Remove screw plugs @) with the O-rings.

Screw in appropriate screw

into the rocker arm shafts.

Pull out rocker arm shafts

Guideline

Screw

Take off the rocker arm (D.

...

Take the shims out of the valve spring retainers and lay them
to one side according to their normal built-in position.

Pretension the valve springs using the special tool.

Valve spring mounter (59029019000) (

p. 298)

Insert for valve spring lever (77029041200) (

p. 302)

Remove valve keys

and relax the valve springs.

Remove valve spring retainer

and the valve spring.

Pull the valve out of the valve guide from below and remove

valve stem seal@) and valve spring seat

C,.

205

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды