Husqvarna F2303Q0 Скачать руководство пользователя страница 51

Страница: 51 / 322

HANDLEBAR,CONTROLS 7

Danger

Danger of poisoning

Exhaust gases are toxic and

inhaling them may result in unconsciousness and
death.
- Always make sure there is sufficient ventilation

when running the engine.

Use effective exhaust extraction when starting or

running the engine in an enclosed space.

Start the engine and let it run at idle speed. Move the handle
bar to and fro over the entire steering range.

The idle speed must not change.

If the idle speed changes:

- Adjust throttle cable play. (

p. 49)

Ad"ustin throttle cable la

Info

If the correct routing of the throttle cables has already been secured, the fuel tank does not need to be

removed.

Preparatory work

Remove the right side cover. (

p. 100)

Remove the air filter box cover. (

p. 96)

Remove the seat. (

p. 1 00)

Remove the fuel tank. (

p. 102)

Check throttle cable routing. (

p. 48)

Main work

Move the handlebar to the straight-ahead position.

Push back sleeve

Loosen nut@.

- Turn adjusting screw

in as far as possible.

Loosen nut

Push cold start button

all the way to the stop.

- Turn adjusting screw

so that the cold start button moves

to the basic position when the throttle grip is turned to the
front.

- Tighten nut

- Turn barrel adjuster

so that there is play in the throttle

cable at the throttle grip.
Guideline

Throttle cable play

Tighten nut

Slide on sleeve

3 ... 5 mm (0.12 ... 0.2 in)

Check the throttle grip for smooth operation.

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды