manualshive.com logo in svg

Asentria TeleBoss 830, Руководство пользователя

Поделиться
Скачать
Asentria TeleBoss 830 Скачать руководство пользователя страница 37

TeleBoss 830 2.11.370 STD User Manual 

 

Page 37 

 

Alarm/Event Definitions  

This will display a menu tree which contains all of the sensor and data event settings options. 

 

Action Definitions

  

This option displays a menu to configure the actions possible when events are detected. 

 

General Settings

  

The General Settings option displays a menu where you can set the site name, answer string, 

confirmation prompt, date/time, and other general settings.   

 

Event Log Settings

  

This option brings up menu for configuring and displaying the Events Log.

 

 

Audit Log Settings  

This option brings up menu for configuring and displaying the Audit Log. 

 

 

Network Settings 

The Network Settings menu contains all of the options pertaining to network communication.  The 

IP Routing 

& Restrictions Feature Guide

 on the Asentria Information Portal will have additional information and 

configuration examples for various features covered under the Networking Settings menu 

 

 

Note:

 The TeleBoss does not heed changes to network configurations while you are connected to a 

command processor via Telnet. Changes, including population of the candidate default router set, are 

pended until all network-based command processor sessions have ended.  Open FTP connections 

will fail if these settings are changed during an open connection.  A Web Interface connection will fail 

if the Ethernet IP address is changed. 

 

 
TeleBoss 830 - Network Settings 
A) Ethernet Settings 
B) IPv4 Default Router                  [0.0.0.0] 
C) Name Resolution Settings 
D) Network Command Processor Duplex     [FULL] 
E) Inactivity Timeout                   [0] 
F) IP Record Collection Settings        [OFF] 
G) Web Interface Settings               [ON] 
H) EventSensor Reporting Settings 
I) SNMP Settings 
J) FTP Settings 
K) PPP Settings 
L) Email Settings 
M) Real-Time Socket Settings 
N) Routing Settings 
O) DSL Settings 
P) VPN Settings 
Q) CPE Settings 
R) Ethernet Expansion Settings 
   Note: Changes to IP Address, Subnet Mask, or Router 
         Address will not take effect until any open 
         network command processor sessions are ended. 
 

 

Ethernet Settings  

This option displays the menu where you can configure the two Ethernet interfaces. 

 

Содержание TeleBoss 830






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды