Asentria TeleBoss 830 Скачать руководство пользователя страница 69

Страница: 69 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 69

Real-Time Socket Push Port Number

This option sets the TCP-port number the RTS push should use. The default setting is port 3000.

Real-Time Socket Push Retry Timer

This option sets the number of minutes (1 to 255) to wait before retrying an RTS push that has previously

failed. The default setting is 5 minutes.

Real-Time Socket Settings as accessed via Web UI

These same settings can be configured from the Web Interface by navigating to the Networking tab in the

Settings Menu section of the left hand menu and selecting Real-time Sockets.

Routing

The following is a top-level overview of the TeleBoss routing settings. For more detailed configuration and use

instructions for all of these please refer to the

IP Routing & Restrictions Feature Guide

on the Asentria

Product Information Portal.

Static Route Settings

Static routes are network routes that specify in a more or less permanent way (static) that traffic to a certain

destination (destination host or destination network) gets routed out a certain interface or via a certain

gateway.

Static routes give you the ability to fine-tune how outbound network traffic leaves the unit for up to eight

different IPv4. You can specify a gateway or interface. If you specify a gateway only then the frame will be IP-

addressed to the destination subnet and transmitted to the gateway, and the gateway needs to be either a

local Ethernet subnet or the peer of a PPP connection (be it Wireless or Dialup Modem). If you specify an

interface, regardless of specifying a gateway, then the frame will be transmitted out that interface.



Note:

Specifying that certain traffic goes out a PPP interface does not cause PPP to be raised when that

traffic needs to leave the unit. If a PPP interface is down then any static routes that specify a PPP

interface are effectively disabled.



Note:

Currently there is no support for Dialup Modem PPP and Wireless Modem PPP to be functional at

the same time. The effect is that if you specify a static route with Wireless Modem PPP interface when the

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды