Asentria TeleBoss 830 Скачать руководство пользователя страница 117

Страница: 117 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 117

Event Actions

Choosing this option displays the Actions List, a menu where the action string for the event is configured.

This field will be empty [ ] if no actions have been configured, and will show [*SET*] if one or more actions

have been configured. Refer to the

Actions List

for more information.

Event Message

Set the text string to be delivered with this event’s action. The default setting is "Reset Event". The
maximum length is 80 characters.

Event Class

Set the class for the event. When this option is selected, a list of the classes previously defined in the

Class Table

is displayed. Select one to be assigned to this event. The default is Info.

Event Trap Number

Set the number to be sent with any SNMP traps for this event. The default is 543, but the trap number

can also be set in the range of 1000

– 1199 as needed.

Delay After Reset (seconds)

Enter the number of seconds to wait after unit finishes booting before executing the Event Action(s) that

have been set for this event. The default is 0, maximum is 3600 (1 hour).

Reset Event Settings as accessed via Web UI

The Reset Event Settings can also be configured via the Web Interface. Navigate to the Events menu and

select Reset Event to bring up the page.

Action Definitions

This menu is where you configure all of the actions possible when events are detected.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды