Asentria TeleBoss 830 Скачать руководство пользователя страница 7

Страница: 7 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 7

DC Power Card Wiring Instructions

This section describes the connection to the 30 watt DC power card, which supports either 24VDC or

-48VDC power options, and features a Phoenix terminal block with screw clamp connectors.

Wiring connections to DC power can be made using customer supplied wiring, or one of the two optional

wiring kits that may be purchased with the unit.

This unit should be assembled and installed by a qualified technician who can ensure the power source is an

isolated, SELV (Safety Extra Low Voltage) circuit for -48VDC installations. The 24VDC option does require an

isolated circuit.



Note:

The DC input should be protected by an external 2A DC rated slow Blow Fuse suitable for

branch circuit protection, at the power supply or within the building circuitry. The input DC power

current limiting fuse circuit is provided for by the end user, and is required for unit operation in

compliance with safety agency approvals.

The DC power supply option has 4 input connections. This gives the user the ability to connect this unit to a

primary and an auxiliary DC power source.



Caution:

DANGER! FIRE HAZARD! DO NOT LEAVE AN UNCONNECTED WIRE EXPOSED! DO

NOT CONNECT THE UNIT TO ANY OTHER EQUIPMENT UNTIL YOU KNOW THE UNIT POWERS

UP CORRECTLY!



Attention

DANGER! RISQUE D'INCENDIE! NE PAS LAISSEZ PAS TRAINER LES FILS NON

CONNECTES! NE CONNECTER L'APPAREIL A TOUT AUTRE EQUIPEMENT QU'APRES AVOIR

VERIFIE QUE SON ALIMENTATION ELECTRIQUE FONCTIONNE CORRECTEMENT!

Asentria TeleBoss products purchased with the DC power option can also be purchased with one of two

optional wiring kits, 5006-026 or 5006-025. Optionally, customer supplied cabling can be used. Wiring

connection instructions for -48VDC and 24VDC are outlined below.

Connection to DC Power

Run two sets of wire to the TeleBoss power input. For A/B redundant systems one circuit should be feed from

the A plant distribution, and one circuit from the B plant distribution. If A/B redundant power feeds are not

required ignore all instructions for B side power feeds.

Ensure the rack that the unit is mounted in is properly grounded. Measure the resistance between the rack

and building steel, aisle ground, or other properly grounded locations. The resistance should be <1 ohm. If this

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды