Asentria TeleBoss 830 Скачать руководство пользователя страница 31

Страница: 31 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 31

Web Interface Status Pages

Sensors

The Sensor Status page is a page with the status of all internal and external EventSensors.

To configure the settings for any sensor, click the blue text associated with the sensor point and the user will

be redirected to the EventSensor configuration page for that EventSensor.

Alternately a user can use the menu tree on the left hand side of the screen. Select Events and then the

submenu EventSensors. Click the EventSensor in the upper section to reach the configuration page for any

specific sensor point.

The number of sensors in their alarm state will be displayed at the top of the page. The grey bar will be

highlighted red for the section with a sensor in the alarm state and the virtual LED will be lit red.

Show <ALL/ENABLED> Sensors

The Show drop-down box at the top of the page toggles between ALL and ENABLED sensors. If toggled to

ENABLED only the sensors that have been enabled in their configuration page will display. The default is

ALL.

XML

This link will display the page information in XML format.

Date/Time

The date and time that the unit is set to are displayed in the upper right corner. The Date and Time can be

adjusted in the

Date/Time Setup

menu under General Settings.

Output Control

To toggle any relay, navigate to the Output Control Status display. Click the View Mode button.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды