Asentria TeleBoss 830 Скачать руководство пользователя страница 18

Страница: 18 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 18

MDM (Modem)

The MDM LED lights solid green whenever the modem is connected and blinks when the modem is dialing

out.

ETH (Ethernet)

The Link LED lights solid green whenever an active Telnet or FTP connection is made to the unit.

ALM (Alarm)

The Alarm LED should be lit if any input or output is in the event state.

25% - 75% - 100%

The T830 has three LEDs to indicate file full status. A blinking percentage full LED indicates the database

has less than the amount indicated by that LED, but more than the previous. A solid lit LED indicates the

database percentage is at or over the value for that LED.

Expansion Card n

Each optional Expansion Card has eight LEDs associated with it. A lit LED would indicate that IO point is in

the alarm or active state. Relays light if the relay is energized. For a high density cards the LEDs will light if

any one of 8 associated IO points go into the active or energized state. Power output points (5V or 15V) do

not have an alarm state, so LEDs would not light. The LEDs would not be used for a modem, Ethernet or

serial expansion card.

Back Panel

T830-0

T830-2

T830-6

The TeleBoss back panel is configured (from right to left) with a bay for the optional run-time battery or DC

power card, AC power jack, RJ45 Sensor port, bank of 8 DIP switches, MMC memory I/O card slot, two RJ45

Ethernet ports, two RJ45 RS232 serial ports, Reset button, one RJ11 serial POTS modem port (in installed).

Depending on the version ordered there could be either two or six expansion bays for optional Expansion

Cards that expand the functionality of the unit with wireless modem and/or a variety of sensor and I/O options.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды