Asentria TeleBoss 830 Скачать руководство пользователя страница 20

Страница: 20 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 20

The DB9 female cable end which mates with the serial port connectors of connected devices will often have a

pair of screw-down cable screws. These cable screws should be used to assure a solid connection of the

cable with the device. The TeleBoss will come with adapters to connect the DTE serial ports with the DCE

ports on a computer. Optional USB adapters are available. See the

Access via a Serial Connection

section for

instructions.

Default settings for the serial ports are 19200-baud, 8-bit word length, no parity, and one stop bit (19200,

8N1). Use the internal setup menu to adjust these settings.

Internal Modem

If a dialup POTS modem is installed, an RJ11 (typical U.S. phone) connector is used. A POTS (analog)

dialup phone line is inserted into this connector. The modem installed within this unit is FCC certified. For

further information, consult the

Internal Modem Guidelines

appendix or the serial number label on the bottom

of the T830.



CAUTION:

To reduce the risk of ﬁre, use only No. 26 AWG or larger telecommunication line cord.



ATTENTION:

Pour éviter tout risque d'incendie, n'utilisez que des câbles électriques de diamètre

supérieur à 0,4 mm (AWG ≤ 26)

Expansion Card Slots

The TeleBoss can be ordered with no Expansion card bays, or with either two or six Expansion Card bays in

which optional Expansion Cards can be installed to expand the capabilities of the unit. See the

I/O points and

Expansion Cards

section of this manual for more information on Expansion Cards.

DIP Switches

The bank of 8 DIP switches on the back panel of the T830 are used to control the baud and parity settings of

I/O2, to set the operational mode for I/O2. The following table shows how to set the various DIP switches to

obtain certain settings:

I/O 2 Baud

SW1

SW2

2400

DOWN

9600

DOWN

19200

DOWN

115200

I/O 2 Word, Parity SW3

8N1

DOWN

7E1

I/O 2 Mode

SW4

Command Mode

DOWN

Data Mode



Note:

For settings that can be set either via DIP switch, internal menu settings, or Setting Keys, the

TeleBoss always pays attention to the last setting, regardless of how it was done. So if the internal setting

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды