Asentria TeleBoss 830 Скачать руководство пользователя страница 67

Страница: 67 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 67

Email Settings

This option displays the Email settings menu where you can configure the SMTP server address, Email

domain name and authentication parameters.

TeleBoss 830 - Email Settings
A) SMTP Server Hostname/IP Address []
B) Email Domain Name [asentria.com]
C) Authentication (LOGIN) [OFF]

SMTP Server Hostname / IP Address

Enter the hostname or IP address of the outbound mail server. The maximum length is 64 characters.

Email Domain Name

This field is used to set the Email domain name, e.g. @

domain_name.com,

which is used when the TeleBoss

sends an Email. The default setting is “ASENTRIA.COM”. The maximum length is 48 characters.

Authentication (LOGIN)

This option displays a menu to configure the credentials that may be required by your server for SMTP

authentication. Some SMTP servers require an authentication to relay Emails. The default setting is OFF.

TeleBoss 830 - Email Authentication Settings
A) Authentication Enabled [OFF]
B) Username []
C) Password [********]

Authentication Enabled

This is an ON/OFF toggle to enable Email authentication. The default setting is OFF.

Username/Password

Enter the login credentials as required. The maximum length for each is 48 characters.

Email Settings as accessed via Web UI

These same settings can be configured from the Web Interface by navigating to the Networking tab in the

Settings Menu section of the left hand menu and selecting Email.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды