Asentria TeleBoss 830 Скачать руководство пользователя страница 137

Страница: 137 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 137

Backing Up & Restoring Settings

Web Settings Backup

To back up the settings file from the Web Interface, select Administration on the left hand menu, then select

System Administration from the submenu. There are two different option for backing up settings.

The "Get Settings from Unit" option will download a text file of all the settings keys and all scripts on the unit.



Click the "Retrieve Settings" button



Save the text file as a back up for this unit.

The "Get Non-Default Settings from Unit" section will only retrieve the settings that have been changed from

the factory default settings. This will be a much shorter settings key file. These file will be most useful in

cloning settings onto new units from the factory or from units that have been reset to factory default settings.

CLI Settings Backup

Backing up using Xmodem or ASCII

For an [X]modem or [A]SCII settings back up, using a terminal emulator that supports either session logging

or Xmodem transfer is recommended. Examples of open source emulators that support at least one of these

are TeraTerm (

http://ttssh2.sourceforge.jp/index.html.en

) and PuTTY

(

http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html

Steps:

1. Establish a Telnet/SSH/Serial connection to the unit.

2. Issue the command

SK GET.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды