Asentria TeleBoss 830 Скачать руководство пользователя страница 120

Страница: 120 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 120

Numeric Message

This is the series of digits (typically callback number) sent to a numeric pager.

Post Callout Delay

This is the number of seconds the unit will wait before sending the pager ID. The default setting is 15

seconds.

Post ID Delay

This is used to set the number of seconds the unit will wait before sending any message data. The default

setting is 5 seconds.

Pager n Settings as accessed via Web UI

The same pager settings are located at the bottom of the Actions Settings page. They would be accessed by

selecting Events on the left hand menu and the choosing General Actions. Use the drop down options in the

grey Pager header box for additonal pagers.

Post ID Delay

sets the number of seconds (0 to 255) the unit will wait before sending any message data.

Default setting is 5 seconds.

Action Settings

This menu is used to configure various general action parameters, such as action schedules and event

reminder intervals

TeleBoss 830 - Action Settings
A) Callout Attempts [5]
B) Callout Delay (seconds) [60]
C) Action Schedule [OFF]
D) Reminder Interval (minutes) [120]
E) Asentria Alarm Version [1.1]
F) Require Asentria Alarm ACKs [OFF]

Callout Attempts

This option is used to set the total number of times to attempt dispatch, Malert or modem callouts if previous

attempts fail. The default setting is 5.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды