Asentria TeleBoss 830 Скачать руководство пользователя страница 93

Страница: 93 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 93

General Security Settings

This section contains global Password/Security Settings that set security options that are required for

every

user who attempts to log into the TeleBoss.

TeleBoss 830 - Global Password/Security Settings Menu
A) Show Username/Password Prompt [OFF]
B) Globally Allow Access via [MTFR]
C) Button Tap Allows Console Access [ON]

Show Username / Password Prompt

This is an ON/OFF toggle to set whether a prompt for logging in is displayed. The default setting is OFF.

Globally Allow Access via

This selection displays a menu allowing you to toggle ON or OFF access via Modem, Telnet (Ports 23, 200x,

210x), FTP, and Real-Time Socket.

These are abbreviated: MTFR. The default setting for all is ON.

Button Tap Allows Console Access

This is an ON/OFF toggle to give access to a user who has forgotten their log on credentials. This is an

insurance policy against locking yourself out of the unit. When set to ON, the user can tap the Reset button 5

times quickly (1-2 times per second), at which point the LEDs on the front panel will flash for a few seconds.

The user will then have immediate Console access using the default MASTER username and password

(admin/password). The default setting is ON.

If you do not want the Button Unlock feature enabled, for example in environments where physical access is

not assumed to be trusted with access, then be sure to turn it OFF.

If you lock yourself out and gain access again with the Button Unlock feature, remember to reconfigure the

settings that were defaulted by the Button Unlock feature to maintain your prior security configuration!

These are the settings that are defaulted by this process:

From the SETUP M

enu →Security Settings menu:



Security Mode set to USER PROFILES



Specific Security Settings→ User 11: →User Name set to

admin

, Password set to

password

and Setup/Status Rights set to MASTER



Specific Security Settings→ Authentication Settings→ Local Command Requires Password
set to OFF



General Security Settings→ Globally Allow Access via set to every method of connecting

General Security Settings as accessed via Web UI

The General Security Settings as described in the last section can also be set from the Web Interface.

Navigate to the Security section on the left hand menu and the select General Security Settings.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды