Asentria TeleBoss 830 Скачать руководство пользователя страница 157

Страница: 157 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 157

Cet appereil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques

de Classe A prescrites dans la norme sur le matériel brouilleur :"Appareils Numériques", NMB-003 édictée par

le ministre des Communications.

Warranty Information

Asentria Corporation hereby warrants that it will, as the buyers sole remedy, repair or replace, at its option,

any part of the T830 which proves to be defective by reason of improper materials or workmanship, without

charge for parts or labor, for a period of 12 (twelve) months. This warranty period commences on the date of

first retail purchase, and applies only to the original retail purchaser.

To obtain service under this warranty, you must obtain, by telephone, postal letter, or email, a return

authorization number from Asentria Technical Support. This authorization number may be obtained by

contacting Asentria Technical Support at the address and/or phone number below. The defective unit is to be

returned to Asentria with shipping prepaid, and the return authorization number must be clearly marked on the

outside of the package containing the defective unit.

The dealer's bill of sale or other satisfactory proof of the date of purchase may be required to be presented in

order to obtain service under this warranty.

This warranty applies if your T830 fails to function properly under normal use and within the manufacturer's

specifications. This warranty does not apply if, in the opinion of Asentria Corporation, the unit has been

damaged by misuse; neglect; or improper packing, shipping, modification, or servicing by other than Asentria

or an authorized Asentria Service Center.

In no event shall Asentria Corporation be liable for any loss, inconvenience or damage, whether direct,

incidental, consequential or otherwise, with respect to the T830. Asentria Corporation's liability shall be

limited to the purchase price of the T830. No warranty of fitness for purpose, or of fitness of the T830 for any

particular application is provided. It is the responsibility of the user to determine fitness of the T830 for any

particular application or purpose.

This warranty gives you specific legal rights. These rights may vary from state to state, as some states do not

allow limitations on liability.

You may request information on how to obtain service under this warranty by contacting Asentria Technical

Support at the address and phone number below:

Asentria Technical Support

1200 North 96th St.

Seattle, WA 98103

206.344.8800

[email protected]

www.asentria.com

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды