Asentria TeleBoss 830 Скачать руководство пользователя страница 66

Страница: 66 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 66

Firewall

This is an ON/OFF toggle to enable or disable the PPP Modem firewall. The default is ON.



Note

: The firewall for PPP Hosting and PPP Dialout are the same setting. Changing the setting in one

menu will update the PPP firewall for all POTs modem functions.

Route Test Settings

This menu allows you to configure up to three IP addresses to ping on a regular basis. If any of the configured

addresses are up then the unit will assume Ethernet is a reliable way of sending SNMP traps. If all configured

addresses are down then the unit will fall back to PPP dialout in order to maintain reliable network connectivity

for sending SNMP traps.

TeleBoss 830 - Route Test Settings
A) Route Test Enable [OFF]
B) Minutes Between Tests [10]
C) IP Address 1 []
D) IP Address 2 []
E) IP Address 3 []

Route Test Enable

This is an ON/OFF toggle to enable route testing. Default setting is OFF.

Minutes Between Tests

This field sets the number of minutes (0 to 65535) to wait between each round of testing. Default setting is 10

minutes.

IP Address n

These fields set the hostnames or IP addresses to ping for the test.

PPP Settings as accessed via Web UI

These same PPP settings

can be configured via the

Web Interface. The

settings for PPP Dialout,

PPP Hosting, and Route

Testing are all on the same

page. They are reach by

navigating to Networking in

the Settings Menu and

selecting the PPP

submenu.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды