Asentria TeleBoss 830 Скачать руководство пользователя страница 40

Страница: 40 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 40

Ethernet Settings

Ethernet Settings displays the following menu where each of the two installed Ethernet cards can be

configured.



Note

: If an Ethernet Expansion card is installed the Ethernet ports are configured at option U)

Ethernet

Expansion Settings.



Note:

The TeleBoss does not heed changes to network configurations while you are connected to a

command processor via Telnet. Changes, including population of the candidate default router set, are

pended until all network-based command processor sessions have ended. Open FTP and RTS

connections will fail if these settings are changed during an open connection. A Web Interface connection

will fail if the ETH1 IP address is changed as soon the submit button is pressed.



Security Note:

If the TeleBoss is going to be exposed to the Internet, make sure to use the other security

features available within the unit to prevent unauthorized access to your network, including strong

passwords. See the

Securing a SiteBoss or TeleBoss

Feature Guide for additional information.

TeleBoss 830 - Ethernet Settings
A) Ethernet 1
B) Ethernet 2

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды