Asentria TeleBoss 830 Скачать руководство пользователя страница 84

Страница: 84 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 84

Wireless Modem

Below is a brief description of the menu configurations options. For a complete description of the setup and

operation of the Wireless Modem, please refer to the

Wireless Modem Feature Guide

on the Asentria Product

Information Portal. Contact Asentria Tech Support for more information.

If the optional Wireless Modem expansion card is not installed in the TeleBoss, this menu is displayed, but

changing any of the settings will not do anything, except for the PPP/Wireless User Name and Password

settings.



Note:

If the optional wireless modem expansion card is not installed in the unit, this menu is displayed,

but changing any of the settings will not do anything, except for the PPP/Wireless User Name and

Password settings (see below).

TeleBoss 830 - Wireless Modem Settings
A) Mode [SMS ONLY]
B) APN []
C) PIN []
D) PPP/Wireless User Name []
E) PPP/Wireless Password [********]
F) Default Route Enable [OFF]
G) Firewall [ON]
H) Advanced Settings

Mode

Mode toggles between SMS ONLY and PERMANENT. SMS ONLY means the modem is only available for

out-

bound SMS messaging. PERMANENT means the modem maintains an “always on” connection with the

network and is available for incoming connections. The default setting is SMS ONLY.

APN

This option sets the Access Point Name (APN) as defined by your wireless provider. The maximum length is

31 characters.

PIN

Set the PIN associated with the SIM card (if any). The maximum length is 15 characters.

PPP Wireless User Name / Password

These options set the login credentials for the PPP connection, as needed. These settings are identical to the

same settings in the

PPP Dialout Settings

– so a change in one menu will change the settings in the

other. The maximum length for each is 64 characters.

Default Route Enable

This is an ON/OFF toggle to enable the wireless interface to be the default route when connected. The

default setting is OFF.

Firewall

This is an ON/OFF toggle to enable or disable the PPP Modem firewall for both PPP Dialout and PPP

Hosting. The default is ON. For wireless modem connectivity the firewall will need to be changed to OFF.

Advanced Settings

The Advanced Settings displays a menu allowing for additional configuration of Wireless Modem Settings.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды