manualshive.com logo in svg

Asentria TeleBoss 830, Руководство пользователя

Поделиться
Скачать
Asentria TeleBoss 830 Скачать руководство пользователя страница 64

TeleBoss 830 2.11.370 STD User Manual     

 

Page 64 

 

 

PPP Dialout Settings

  

This selection displays settings pertaining to making outbound PPP network connections. 

 

PPP Hosting Settings

  

This selection displays settings for hosting a PPP connection. 

 

Route Test Settings  

This selection displays settings for network monitoring/PPP backup connection settings.  This menu allows 

you to configure up to three IP addresses to ping on a regular basis.  If any of the IPs are down, the unit will 

fall back to a PPP dialout in order to maintain reliable network connectivity for sending SNMP traps. 

 

 

PPP Dialout Settings 

This menu is used to configure settings pertaining to making outbound PPP network connections for a POTs 

modem.  

 

Setting Key:

   

net.pppdial.downafter.ftppush 

Values are ON or OFF (default OFF).  ON means that if FTP Push raised PPP, then it kills 

PPP when finished. 

 

 
TeleBoss 830 - PPP Dialout Settings 
A) PPP Dialout Enabled                  [OFF] 
B) Phone Number 1                       [] 
C) Phone Number 2                       [] 
D) Phone Number 3                       [] 
E) Phone Number 4                       [] 
F) User Name                            [] 
G) Password                             [********] 
H) Idle Connection Disconnect (sec)     [60] 
I) Maximum Retries                      [3] 
J) Carrier Detect Timeout (sec)         [60] 
K) Login Sequence Timeout (sec)         [30] 
L) Dialout Modem Init String            [] 
M) IP Address to Suggest                [0.0.0.0] 
N) Firewall                             [ON] 
O) Maximum Dialout Failures             [15] 
 

 

PPP Dialout Enabled  

This is an ON/OFF toggle to enable PPP dialout.  The default setting is OFF.

 

 

Phone Number n   

These fields set the phone number(s) of the PPP host the TeleBoss is to dial into.  The maximum length is 48 

characters each. If the connection fails the unit will try the next phone numbers entered.

 

 

User Name / Password  

Use these fields to set the login credentials that are used to log into the PPP host (maximum length for each is 

64 characters).

 

 

Idle Connection Disconnect (sec)  

This field sets the number of seconds to wait before disconnecting an idle connection.  A setting of 0 means 

the unit does not disconnect due to an idle connection.  The default setting is 60 seconds.

 

Содержание TeleBoss 830






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды