Asentria TeleBoss 830 Скачать руководство пользователя страница 109

Страница: 109 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 109

Event State Actions / Return to Normal Actions

Choosing this option displays the Action List, a menu where the action string for the event is configured. This

field will be empty [ ] if no actions have been configured, and will show [*SET*] if one or more actions have

been configured. Refer to the

Actions List

for more information.

Event State / Return to Normal Class

This option is to set the class for the event. When this option is selected, a list of the classes previously

defined in the

Class Table

is displayed. Select one to be assigned to this event. The default is Info.

Event / Return to Normal Trap Number

This option is for setting the trap number which can be useful when using SNMP trap managers that employ a

trap numbering system to help identify incoming traps. The default trap number for Contact Closure Events is

110, but any number in the alternate range of 1000

– 1199 can be used.

Active Alarm Alias

Inactive Alarm Alias

You can use these options to set a customized name representing the alarm state. These would be used

when reporting events for this sensor. The maximum length is 60 characters for each.

Override Global Reminder Interval

This option is an ON/OFF toggle to override the global reminder interval. If this is set to ON a specific

reminder interval can be set for this event. The default setting is OFF.

Individual Reminder Interval (minutes)

This field sets the time in minutes (0

– 65535) for an action to be repeated if the contact closure that triggered

the alarm is still in the “active” state. When the sensor has been returned to the inactive state, the reminder
interval is no longer in effect. The default setting is 120 minutes.

Contact Closure Settings as accessed via Web UI

The Contact Closure settings would be accessed from the EventSensor submenu under the Events section on

the left hand menu. Click the hyper link in the Status section for the EventSensor to configure and click on

they grey bar to open the settings section for the contact closure point desired.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды