Asentria TeleBoss 830 Скачать руководство пользователя страница 82

Страница: 82 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 82

Modem Settings

The Modem Settings menu displays two submenus for configuring either the optional POTs Dialup Modem or

the optional Wireless Modem expansion card. These menu settings will display even if a modem is not

installed. If the POTs modem or Wireless modem card is not installed, changing the settings will have no

effect on the TeleBoss' functionality.

TeleBoss 830 - Modem Settings
A) Dialup Modem
B) Wireless Modem

Dialup Modem

This option brings up a menu for configuring the settings for an optional POTs modem card.

Wireless Modem

This option will bring up a menu for configuring an optional wireless modem card.

Dialup Modem

The following is a top level settings configuration overview for the optional Dialup POTs modem. For

additional information see the

Dial Up Modem Feature Guide

on Asentria Product Information Portal or

contact

Asentria Technical Support

If a dialup POTS modem is installed, an RJ-11 (typical U.S. phone) connector is used. A POTS (analog)

dialup phone line is inserted into this connector.



CAUTION:

To reduce the risk of ﬁre, use only No. 26 AWG or larger telecommunication line cord.



ATTENTION:

Pour éviter tout risque d'incendie, n'utilisez que des câbles électriques de diamètre

supérieur à 0,4 mm ( AWG ≤ 26)

TeleBoss 830 - Dialup Modem Settings
A) Data Format [8N1]
B) Duplex [FULL]
C) Init String [ATM1]
D) Inactivity Timeout [0]
E) Upon Modem Connect Go Directly To [LOGIN]
F) TAP Init String [ATM0]
G) TAP Uses 8N1 Data/Parity/Stop [0]

Data Format

This option toggles settings for word length, parity, and stop bit settings. The available options are: 8N1, 7E1,

7O1, and 7N1. Default setting is 8N1.

Duplex

Duplex sets the echo settings for the modem command processor. Full duplex causes the TeleBoss to echo

all characters sent to the remote device. Half duplex turns off character echo. Default setting is FULL.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды