Asentria TeleBoss 830 Скачать руководство пользователя страница 101

Страница: 101 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 101

Field Name

This option sets the name given for the alarm field. This name must be unique, is limited to 12 characters,

and it must not contain any spaces. It can contain alphanumeric characters and the underscore, but it must

start with a letter. These field names

are case sensitive. If left blank, you can refer to the field by it’s field

letter (A,B, etc…).



Note:

To avoid naming conflicts, the TeleBoss does not allow duplicate field names. The unit will respond

with “Invalid Entry, Press any key to continue” if a duplicate field name is entered.

Field Line Number

The Line Number sets the optional line number the field should be limited to in multiline records. The default

setting is 0.

Field Type

Type toggles between Alpha and Numeric. Alpha is used for most alphanumeric data alarming, and Numeric

is used if you need to alarm on a range of numbers. The default setting is Alpha.

Data Alarm Field Settings as accessed via Web UI

All of these settings can be configured via the Web Interface. From the Events tab of the left hand Settings

Menu select the Data Alarm/Filters option to access the settings page. The Field section of the page is

available to set all of these Data Alarm Field Settings. It may be more convenient to set multiple field

definitions here, since they are altogether on one page.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды