manualshive.com logo in svg

Asentria TeleBoss 830, Руководство пользователя

Поделиться
Скачать
Asentria TeleBoss 830 Скачать руководство пользователя страница 12

TeleBoss 830 2.11.370 STD User Manual     

 

Page 12 

 

Connect to that serial port using any terminal emulator such as TeraTerm  

(

http://ttssh2.sourceforge.jp/index.html.en

) or Putty 

(

http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html

).  I/O 2 is set to 19200 baud, 8N1  

(8 data bits, no parity, 1 stop bit, no flow control) by default.   

 

The command port is not password protected by default.  The TeleBoss does not have a default command 

prompt.  Type 

STATUS

 and press <Enter>.  You will be presented with a Status screen similar to the 

following.  When the Status screen appears, the unit is successfully connected and ready for use.  See the 

Command Line Interface

 chapter for information on how to configure and control functions of the TeleBoss via 

this interface. 

 

 
status 
TeleBoss 830 2.11.370 STD  -  Status 
Site Name       : 830-000000000 
Serial Number   : 000000000        Eth 1    : DHCP 
Date            : MON 09/24/2018   IP Addr  : 192.168.90.76 
Time            : 20:38:45         MAC Addr : 00:10:A3:60:49:91 
Memory          : 63488K           Eth 2    : STATIC 
% Full Alarm    : OFF              IP Addr  : 0.0.0.0 
No-Data Alarm 1 : OFF              MAC Addr : 00:10:A3:60:49:92 
No-Data Alarm 2 : OFF              Modem    : None 
Duplex          : FULL 
------------------------------------------------------------------------- 
Port   Baud/Etc.  Recs     Bytes    Full Wrap Name 
IO1  : 19200,8N1  00002170 00131072   1% OFF  I/O 1 
IO2  : 19200,8N1  00000000 00000000   0% OFF  I/O 2 
 
COMPLETE 

 

 

Configuring Ethernet Settings via IO2 

For instructions on how to access the command line interface serially via IO2 see the 

Access via a Serial 

Connection

 section.   

 

Once you have successfully connected to the Command Line Interface, configure the Ethernet Settings by 

taking the following steps: 

 

a.  Type 

SETUP

 

and press <Enter> from the TeleBoss command prompt. 

b.  Type 

A

 to select Network Settings from the menu. 

c.  Type 

A

 at the Network submenu to select Ethernet Settings. 

d.  Type 

A

 from the Ethernet submenu to select Ethernet 1. 

 

 
TeleBoss 830 - Ethernet 1 Settings 
A) IPv4 Mode                            [STATIC] 
B) IP Address                           [0.0.0.0] 
C) Subnet Mask                          [255.255.255.0] 
D) Router Address                       [0.0.0.0] 
E) NAT                                  [OFF] 
F) VLAN Settings 
G) IPv6 Settings                        [OFF] 
 

 

e.  Set the Mode, as needed, to the desired setting by selecting 

A

. The default is static. The other options 

are DHCP or VLAN. 

f. 

To set a static IP address, type 

B 

and enter an IP Address. 

Содержание TeleBoss 830






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды