Asentria TeleBoss 830 Скачать руководство пользователя страница 86

Страница: 86 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 86

Fail Threshold

This field sets how many ping checks in a row must fail before the modem or TeleBoss is power cycled.

Range is 2 to 50, default is 5.

RX Reset

This check box is an on/off setting that determines whether the connectivity check trigger is inhibited if any

data is received on the wireless interface. The default is ON (checked).

Wireless Modem Settings as accessed via Web UI

The Wireless Modem settings are accessed in the Web Interface using the Communication option on the left

hand menu and then select Wireless Modem.

The upper section of the Wireless Modem Web Page is a Status Page for the Wireless Modem. The

information will be filled in based on the type of modem installed. For that reason, the status information

section will vary. This section displays information such as if the modem is connected with the wireless

network, Signal Strength, the IP Address of the modem along with basic information on the modem itself and

any installed SIM. This would be the same sort of information that you can access using the

?W INFO

from

the command line interface.

The lower section cover the settings available to configure your wireless modem. These are the same

settings as covered above.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды