Asentria TeleBoss 830 Скачать руководство пользователя страница 102

Страница: 102 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 102

Data Alarm Macro Settings

This option displays the menu for configuring up to 100 macros to be used for data alarming. Data alarm

macros provide a way to define up to 100 equations that can be used in one or more data alarm equations.

Each macro consists of an equation and an associated name that can be used to reference the macro in a

data alarm equation. Refer to the

Data Alarm and Event Configuration Feature Guide

for a more in-depth

explanation of configuring data alarm equations. Contact

Asentria Technical Support

for more information.



Note:

Macro names and data field names cannot start with $.



Note:

Do not start a macro name or data field with AND or OR.

TeleBoss 830 - Data Alarm Macro Settings
A) Macro 1 []
B) Macro 2 []
...
P) Macro 16 []
Q) Next Macro Page

Enter your Selection: a

TeleBoss 830 - Settings for Data Alarm Macro 1
A) Name []
B) Equation []

Name

The macro name is the name by which the macro is referenced in any data alarm equation, and can be up to

16 characters in length. Macro names and data field names are not case sensitive. A macro cannot be given

the same name as a data field or another macro.

Equation

The macro equation is entered the same way as a data alarm equation. A macro equation cannot refer to

another macro. The macro equation can be up to 160 characters in length.

Data Alarm Macro Settings as accessed via Web UI

The Macro Settings

can be configured via

the Web Interface.

They can be access

from the Events tab

on the Data

Alarm/Filters page.

Use the drop down in

the grey bar to bring

up additional Macro

lines to configure.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды